P2135 identifies a disagreement in related position signals, commonly the two throttle-position signals. With a reduced-power warning, the priority is safe handling of the vehicle and an accurate diagnosis, not a reset that briefly restores normal response. Confirm the manufacturer's definition for your exact vehicle before deciding whether the repair belongs at a connector, wiring circuit or throttle assembly.
A warning that disappears after restarting does not establish that the cause is gone. Preserve the evidence, describe when the loss of response occurred, and ask what measured failure supports the proposed part.
Correlation does not mean identical readings
Electronic throttle systems use position information to check whether the commanded and reported behavior makes sense. The related signals must follow the relationship specified for that design. They do not necessarily display identical voltages or percentages.
The Mitsubishi P2135 diagnostic description provides one manufacturer example: its monitor evaluates the relationship between main and secondary throttle-position signals, with defined criteria and a default throttle position during fail-safe operation. Those criteria belong to that application. Copying its voltages or timing into a test on another vehicle would be misleading.
Do not identify the failed part from a generic scan-tool phrase containing “throttle/pedal” alone. Ask which sensors and circuits the vehicle's own definition actually names. The accelerator pedal and throttle body are not interchangeable repair targets just because both participate in controlling engine output.
P2138 after wet weather: distinguish pedal signals from throttle signals
P2138 commonly concerns disagreement between accelerator-pedal position signals. It is a different repair target from the throttle-position signals discussed above. Confirm the vehicle's exact definition before ordering either assembly. A generic scanner phrase containing throttle/pedal is not enough to choose between them.
GM bulletin 07-06-04-019F, November 2017, describes intermittent P2138 and reduced power on its listed 2018-and-prior passenger-car and light-truck applications. Water entering an instrument-panel-to-body connector can disturb the pedal signals carried to the engine controller. It also flags aftermarket circuit connections and reference-voltage faults for attention. The bulletin directs a separate check of applicable guidance for the 2014 ATS.
If the warning follows rain or a wash, record that timing and any dampness you notice safely. Ask whether the shop found a water-entry path and affected connections rather than assuming the pedal itself failed. In the GM case, correcting a leak and addressing connector damage are separate parts of a lasting repair. Do not spray water into the cabin, dismantle trim around airbags or unplug pedal wiring to reproduce the problem.
An independent Mitsubishi P2138 procedure prioritizes a companion P06B0 fault before its pedal-supply, ground and signal checks. That is a specific example of why related electrical codes matter, not a universal instruction to replace a particular component. No voltage, pin number or reset sequence from another vehicle should be substituted for the correct procedure.
Ask which signal relationship failed, how its supporting circuits were checked and what establishes the proposed correction. Wet-weather timing alone is not proof of connector damage, and drying out does not prove a repair. If accelerator response is unreliable, the reduced-power safety guidance below applies even when a restart temporarily restores normal operation.
P2101: actuator performance is different from position-signal correlation
P2101 commonly concerns throttle-actuator control motor range/performance. P2135 asks whether related position signals agree as designed; an actuator-performance concern asks a different question about throttle control and response. Confirm the exact definition for your engine before interpreting either as an assembly-replacement instruction.
The 2014 Volkswagen Passat specification book, page 15, describes a P2101 check involving throttle angle versus the calculated value for the applicable engine section. Other sections use different criteria. Ask which commanded-versus-reported behavior or circuit finding failed on your vehicle; do not borrow numerical limits from that example.
GM PIP5660A, December 2023, covers listed 2019 Cadillac XT4 2.0L LSY and Silverado/Sierra 1500 New Model 2.7L L3B applications with P2101 and/or P1516 and possible reduced power. It identifies possible internal gel contamination and uses a VIN breakpoint to distinguish its replacement path from further service-information diagnosis, including terminal and wiring checks. This is a specific manufacturing-related case, not evidence that cleaning the throttle bore will cure every P2101.
Ask the technician to verify current applicability and explain which branch fits the vehicle. If the report shows P2101 alongside correlation or supply faults, preserve all of them rather than choosing whichever code sounds cheapest to fix. Do not force the throttle plate, spray cleaner into electrical parts or bypass reduced-power protection. Unpredictable accelerator response requires the safe-stop approach below, even if a restart temporarily changes the symptoms.
P0122 and P0123: one input can fail without a correlation code
P0122 and P0123 concern low and high position-sensor circuit input, respectively. They ask a different question from P2135's agreement between signals or P2101's actuator-performance concern. Confirm which component and channel the manufacturer's definition identifies; a generic scanner's “throttle/pedal” label does not establish that the accelerator pedal needs replacing.
Mitsubishi's 2023 manual describes P0122 for the main throttle-position signal, with the sensor integrated into the throttle body on that design. The monitor checks its electrical range. “Low” is not a diagnosis of low idle speed, and “high” is not a conclusion about how hard the driver pressed the pedal.
The corresponding P0123 description includes open circuits, shorts and connection damage among its possibilities. Its diagnostic path considers supply, ground and signal integrity. A high input therefore does not automatically prove a short to power or a defective sensor. These are design-specific examples, not wiring instructions or universal voltage limits.
Ask which input failed, whether supporting circuits were checked and how that evidence distinguishes an assembly fault from a connection problem. Save companion reference-voltage codes and the timeline of any recent intake work. Leave connector measurements and throttle actuation to qualified service. The reduced-power safety precautions below still apply; do not clear the warning or repeatedly restart as a way to continue driving with unreliable response.
Reduced power changes the safety decision
Unexpectedly limited acceleration can make merging, crossing traffic or climbing a grade unsafe. If response is unreliable, leave traffic as safely as possible and arrange assistance rather than repeatedly restarting and trying again. Do not conduct a public-road experiment to discover when the warning returns.
Record whether the warning occurred at startup, during steady driving, after a bump, or after recent service. Note other messages and whether the engine idled normally. If a passenger can safely capture a warning, that can help; the driver should not operate a phone or scan tool while moving.
A steady check-engine light does not override the practical hazard of poor throttle response. The vehicle's behavior and owner-manual instructions matter, not just whether the lamp is flashing.
Save more than one code number
Before erasing anything, collect the full scan report, current versus history status, and available freeze-frame or failure records. Related supply-voltage, position-signal or actuator codes may change where diagnosis begins. A list of disconnected-component codes created during prior work also needs its own timeline.
Ask the shop to identify which faults are present now and which are retained from earlier events. “P2135 was in history” and “the signal disagreement was captured during today's test” are not equivalent findings.
Tell the technician about battery work, intake work, throttle cleaning or connector disturbance shortly before the complaint. Timing can help focus an inspection, but it does not prove the last person working on the vehicle caused the failure.
Ask for signal evidence under controlled conditions
The useful result is a comparison against the manufacturer's expected relationship, not two isolated numbers copied from a scanner. Ask whether the signals were observed together, whether the problem was reproduced safely, and what changed when the fault appeared.
A normal snapshot does not necessarily settle an intermittent complaint. Conversely, a screenshot with different percentages is not proof of failure unless the tool's parameter definitions and the expected relationship are understood. Request an explanation in plain language: which signal stopped behaving as expected, and how was that distinguished from a supply or connection problem?
This is diagnostic work, not an invitation to force the throttle plate open or energize it with improvised wiring. Keep hands and tools away from an electronically controlled throttle mechanism. Do not bypass the system's protective operation to continue driving.
Separate the assembly from its supporting circuits
Before authorizing a throttle body, ask what inspection or testing ruled out the relevant connector and harness problems. The Mitsubishi example includes damaged wiring or connectors among possible causes; it does not make an assembly replacement the answer to every P2135.
A useful estimate names the supported fault and the proposed correction. “Replace throttle body because code says throttle” is much weaker than a report describing the failed signal behavior with the applicable circuit checks completed.
If the proposed diagnosis changes between visits, ask what new evidence changed it. That is a reasonable request, not an accusation. Intermittent faults can require more observation, and the shop should be able to distinguish an unresolved possibility from a confirmed failure.
A bulletin may change the repair scope
GM bulletin 12-06-04-003A, March 2014 addresses P2135 and reduced-power complaints on its listed Buick, Chevrolet, Pontiac and Saturn applications with specified engine RPOs. It directs a sensor-cover repair rather than automatically replacing the complete throttle body for the bulletin condition.
That historical example is valuable because it shows why the part choice must follow exact applicability. It does not mean all throttle bodies have a separately serviceable sensor, nor that the bulletin's procedure is suitable for a different engine. Ask the shop to verify the model, engine, current service information and any superseding instructions before ordering parts.
Do not infer warranty eligibility from the existence of a bulletin. Technical repair guidance and payment coverage are separate questions.
Cleaning, relearning and proof of repair
A dirty throttle bore and a signal-correlation fault are not the same diagnosis. Do not assume cleaning will correct P2135, and do not use a generic pedal sequence as proof that the electronics are healthy. If cleaning, programming or an adaptation procedure is required by the actual repair, the shop should identify that requirement.
The P0507 high-idle guide covers a different question: an idle-speed complaint, including one following throttle service. Similar timing does not make P0507 and P2135 interchangeable.
After repair, ask whether the relevant signal checks passed, whether the reduced-power complaint was addressed and whether any faults remain. Verification should follow the applicable service procedure under safe conditions. Merely deleting the code or observing a normal restart is not a complete explanation of why the repair worked.
Frequently asked questions
Does P2135 mean I need an accelerator pedal?
Not automatically. Confirm the manufacturer-specific definition and the affected signals before selecting a component.
Can a restart fix reduced power?
It may change the current operating state, but it does not establish that the underlying fault has been repaired. Treat recurring or unpredictable response as a safety concern.
Should both throttle readings match exactly?
Only if the manufacturer's parameter definitions require it. Correlation means the specified relationship, not necessarily equal displayed numbers.
Is a complete throttle body always necessary?
No universal answer applies. Circuit findings, component serviceability and vehicle-specific instructions determine the repair scope.