If the engine still cranks but will not start after a crankshaft-position sensor replacement, P0335 is a reason to test the complete signal system. It is not proof that another sensor will fix it. The missing evidence may concern the circuit, the signal reaching the control module, the target the sensor reads, or another part of the no-start diagnosis.
First distinguish crank-no-start from no-crank. In a crank-no-start complaint, the starter turns the engine but it does not run. If the engine does not turn at all, do not assume a stored P0335 explains that different symptom.
What P0335 means
P0335 generally identifies a crankshaft-position sensor circuit fault. This Mitsubishi diagnostic procedure evaluates missing or abnormal pulse information and lists the sensor, wiring and connectors, sensing ring, and control module among possible causes. Its exact criteria and circuit arrangement apply to that vehicle.
The crank signal supplies engine-position and speed information. A usable signal is more than the presence of a sensor in its mounting hole. The system has to produce and deliver the information the control module expects during the conditions being diagnosed.
A code lookup cannot tell whether the signal is absent at the sensor, lost along the wiring, or present but incorrect. Those distinctions are the work of diagnosis.
Make the no-start investigation safe
Avoid repeated long cranking attempts. Follow the owner's manual's starting limits and stop for unusual mechanical noise, smoke, fuel leakage, or strong fuel odor. Do not use starting fluid or bypass starting and safety controls as an improvised test.
If the vehicle stalled in traffic or cannot be started safely, arrange recovery rather than trying to reproduce the failure on the road. Keep clear of belts, fans, and moving parts. A hybrid or automatically starting vehicle requires its own precautions even when the engine is quiet.
Do not work underneath a vehicle supported only by a jack. A crankshaft sensor can be difficult to reach, and accessibility does not make an engine-running or cranking test safe for an untrained person.
Preserve the sequence of events
Save the full scan report and available freeze-frame information before clearing it. Record whether P0335 was present before the replacement and whether other codes appeared afterward. Include any recent battery, starter, engine, transmission, or wiring work.
Tell the shop exactly what changed. Did the engine start once after the repair? Does it fail only hot? Does the starter turn it normally or unusually slowly? Was the earlier symptom stalling rather than a no-start? These observations help define the test, but none proves a particular part is faulty.
Keep the old diagnostic report and the replacement part number. “Crank sensor replaced” is useful history; “sensor failed a documented signal test under the original complaint conditions” is much stronger evidence.
Confirm the replacement and the circuit
Before condemning the next part, the technician should verify the correct application, mounting, connector engagement, and nearby wiring. A replacement cannot fix a damaged terminal or a circuit fault left elsewhere on the vehicle.
HELLA's crankshaft-sensor guidance distinguishes sensor designs and warns against using an ohmmeter when the type is unknown because an inappropriate resistance test can damage a Hall sensor. Connector appearance alone is not a reliable test plan.
Ask what circuit checks were performed using the manufacturer's specifications. Do not apply universal resistance values, jumper power to an unidentified terminal, or assume a sensor that passes a bench test must work correctly in the vehicle.
Ask whether the module sees the right information
Engine-speed data during cranking can be a useful clue, but it should not become a one-number verdict. Ask whether the technician confirmed that the tool's data is supported, updating, and appropriate to the vehicle. A zero or implausible display needs interpretation, not automatic sensor replacement.
The next question is whether the required waveform or signal pattern reaches the control module under the failure conditions. If a scope test is used, the report should identify the circuit, operating condition, and comparison standard. A screenshot without that context is difficult to evaluate.
If the crank information proves valid, the no-start still needs diagnosis. The existence of a stored code should not prevent the shop from considering other required starting conditions through the correct diagnostic sequence.
A damaged target can make a new sensor ineffective
The sensor reads a rotating target, sometimes called a reluctor or sensing ring. Mechanical damage there can matter even if the electrical circuit is intact. The evidence should establish that problem before internal repairs are proposed.
A historical GM TechLink example from November 2020, page 9 describes certain 2020–2021 Encore GX and 2021 Trailblazer vehicles with the 1.2L LIH engine. A no-start with P0335/P0336 could involve damage to both the crank sensor and reluctor, with an underlying mechanical cause. This is not a diagnosis of every Encore GX, Trailblazer, or P0335 vehicle.
The general lesson is to account for the cause of physical damage rather than fitting the same vulnerable part again. Ask the technician to check current applicable service information and document what was actually found. Do not attempt target inspection or engine disassembly from a generic code article.
P0315 after service: verify the required learn without overlooking hardware
P0315 means crankshaft-position system variation has not been learned. After engine, controller or crank-sensor work, ask whether the vehicle requires a specific learning procedure and whether its completion was verified. It is a different question from whether P0335 indicates a usable crank signal.
A Chrysler service-parts note for a specified crank-sensor family describes stored crank-target learning on the applications it discusses beginning with the 2007 model year. It identifies several service events that require relearning and warns that disconnecting the battery does not reset some controllers. This is application-specific information, not a universal reset procedure.
But “not learned” does not guarantee that learning alone will solve the complaint. Hyundai bulletin 15-AT-006, July 2015, addresses specified Genesis DH 3.8-liter applications with P0315 and related misfire complaints. Its diagnosis can involve the sensor or its target/drive plate, followed by the prescribed learning and confirmation. The historical 2015-onward heading should not be extended to every later Genesis or engine.
Ask the shop to separate three findings: whether the crank signal and hardware are sound, whether the correct learning prerequisites were met, and whether the completed procedure resolved the recorded fault. If the learn cannot complete or the code returns, request the next diagnostic finding instead of repeated clearing.
Do not copy a high-speed coast-down routine, free-rev the engine or disconnect the battery to attempt an internet relearn. Required procedures and their safety conditions belong with a qualified technician using current information for the exact vehicle. A flashing warning, severe shaking or stalling still needs safe handling rather than a learn attempt on the road.
Frequently asked questions
Should I replace the crank and cam sensors together?
Not merely because they work with related engine-position information. Each replacement should have supporting evidence. A damaged shared circuit or mechanical problem may survive both replacements. For camshaft codes, see P0340/P0341.
Will a relearn make a no-start disappear?
Only the manufacturer's procedure can establish whether a relearn is required and what prerequisites apply. It cannot be assumed to repair a missing electrical signal or damaged target. Ask which requirement supports the recommendation.
Can a new sensor still be defective?
Yes, but possibility is not diagnosis. Verify the part and installation, then test the signal and circuit before replacing it again. Newness should neither condemn nor clear a component.
What should I request after the repair?
Ask for the identified cause, the relevant pre-repair and post-repair results, and verification under the conditions that caused the original complaint. One successful start does not fully explain an intermittent hot no-start, and clearing the warning does not demonstrate that the signal fault is resolved.