Emissions

P0137 after an oxygen-sensor replacement: explain the low signal before buying another sensor

P0137 low signal versus P0140 rear-sensor no activity: check the actual monitor conditions before replacing another oxygen sensor or converter.

P0137 means the bank 1, sensor 2 oxygen-sensor circuit has met the vehicle's low-voltage fault criteria. It does not automatically mean the replacement sensor is defective, the engine needs more fuel or the catalytic converter needs replacing. The diagnosis must separate a circuit problem from the exhaust condition being measured and the operating conditions of the test.

If the code returned after a repair, keep the old and new scan reports and the replacement part details. “Still low” needs a measurement, a location and a valid test condition before it becomes a useful conclusion.

Confirm which sensor and which signal are involved

Identify bank 1 and sensor 2 from the manufacturer's layout. Sensor 2 is the downstream oxygen sensor in the usual arrangement, but physical location, connectors and exhaust routing must be checked for the actual engine. Do not choose a component by its position relative to the driver's seat or the order in which you can reach it.

Also identify the parameter being displayed. An upstream air-fuel sensor reading should not be judged by the same assumptions as a conventional downstream oxygen-sensor voltage. The scanner's label, units and supported data matter.

P0138 concerns the high-signal side of the downstream circuit. P0135 and P0141 concern heater circuits. Related components do not make these codes interchangeable.

Low at one moment is not the complete failure criterion

The controller evaluates the signal under defined conditions, not simply whether a graph ever reaches a low value. Ask which part of the applicable monitor failed and whether the technician observed that behavior under the relevant conditions.

One Mitsubishi P0137 description evaluates whether the downstream sensor reaches the required maximum signal and also identifies a short-to-ground condition. Its possible causes include circuit faults, the sensor and certain fuel or intake problems. It also explains that catalyst oxygen storage makes downstream switching behavior differ from the upstream sensor.

This does not supply a universal voltage target or mean a healthy downstream graph must copy the upstream graph. A screenshot without operating context cannot establish sensor failure.

P0140: a steady rear-sensor graph is not enough

P0140 concerns no activity detected from the bank 1 sensor 2 circuit. That is a different monitor category from P0137's low-voltage fault. An idle screenshot with little movement does not establish either a failed sensor or a failed catalytic converter.

The Mitsubishi 2023 P0140 description evaluates rear-sensor response during specified changes in operation, with temperature and related-monitor requirements. It does not diagnose no activity merely because the rear trace is steadier than the upstream trace at one moment. Its electrical reference arrangement also remains specific to that design.

Ask which completed monitor or controlled test supports the finding, whether the relevant operating conditions were met and whether the scanner actually supports the selected parameter. Keep heater, upstream-sensor and reference-circuit faults available to the technician rather than deleting them first. Do not imitate the manufacturer's drive cycle, alter fueling or manipulate hot exhaust components to make a graph move. The result should explain the failed response and valid repair verification, not just show that a code was erased.

Do not overlook the sensor's reference circuit

A different Mitsubishi rear-sensor procedure uses an offset on the sensor's ground circuit and distinguishes scan data from measurements referenced to vehicle ground. That design-specific detail is a warning against assuming every wire labeled “ground” is simply interchangeable with chassis ground.

Ask whether the electrical tests used the correct reference points, connector identification and specifications. Do not add an extra ground wire or apply battery voltage to a sensor circuit because an online test suggests it.

A low displayed value can lead to different diagnostic branches depending on the design. The correct circuit diagram and procedure should determine the test, rather than a generic resistance or voltage rule copied from another vehicle.

Preserve companion codes and recent work

Save all codes, status and available freeze-frame information before erasing anything. Heater, upstream-sensor, mixture or other electrical faults may affect the order in which the diagnosis should proceed. Ask the shop to explain which related results are trustworthy and which need attention first.

Document whether the exhaust, sensor connector or nearby harness was recently disturbed. Provide the new sensor's part number and whether its connector and wire routing matched the original arrangement. A new component does not rule out installation or supporting-circuit problems.

If the engine runs poorly, describe that separately from the warning light. Do not assume an apparently normal idle proves the signal circuit is sound, or that every drivability symptom must come from the downstream sensor.

A damaged pigtail can make another replacement a temporary fix

GM preliminary information PI0937 describes P0137 and related oxygen-sensor codes on the 2013 Buick Verano with the 2.4-liter LEA engine. It identifies contact involving the sensor wiring and the passenger-side axle area and specifies addressing routing as part of the repair.

This is a particular vehicle example, not a universal harness-routing instruction. Do not copy its physical routing method onto another vehicle. Its broader diagnostic lesson is to identify what damaged the part so that a replacement is not exposed to the same condition.

Ask whether the harness was inspected for contact, heat damage or connector problems in the relevant areas. If a fuse is involved, replacing it alone does not explain why it opened. Never install a higher-rated fuse or bypass protection.

An exhaust leak deserves evidence too

GM bulletin 20-NA-065, August 2022 includes P0137 among fuel-trim and oxygen-sensor complaints on its listed 2000–2022 gasoline passenger cars and trucks. It directs technicians to start with service-information diagnosis and provides leak-detection guidance when an intake or exhaust leak is suspected.

That is not proof that every low-signal code is caused by an exhaust leak. Ask where the leak was found, how it relates to the sensor reading and what changed after it was corrected. Similarly, a claim that the engine is running lean needs supporting fuel-system and sensor evidence, not just the word “low.”

Do not block a running tailpipe, introduce arbitrary pressure or use improvised smoke equipment. Leak testing around hot exhaust and fuel-related systems belongs with suitable equipment and trained personnel.

Do not use the code as a catalyst-replacement shortcut

P0137 is not a catalyst-efficiency diagnosis. If a converter is proposed, ask which separate tests support that recommendation and whether the relevant oxygen-sensor information is credible first.

For a sensor recommendation, request the failed response or electrical test. For a wiring recommendation, request the location and nature of the fault. For a mixture-related repair, ask which evidence established the underlying air or fuel problem.

The final record should connect one confirmed cause to the correction and then show appropriate verification. Clearing the code after fitting a sensor does not demonstrate that the low-signal condition has been eliminated.

Frequently asked questions

Can I keep driving with P0137?

The code alone cannot establish safety. Stop safely for severe rough running, a flashing warning light, stalling, unpredictable power loss or suspected exhaust fumes entering the cabin, and arrange assistance.

Can I test the sensor with a cheap meter?

Correct reference points, test conditions and equipment matter. Leave live probing and intrusive testing to a qualified technician. Never work under a vehicle supported only by a jack or touch hot exhaust components.

What if it only happens occasionally?

Keep the event history and saved data. A currently normal reading does not disprove an intermittent fault; the shop should investigate the conditions and relevant connections rather than repeatedly replace parts without evidence.

Search this site's starter library by trouble code, symptom or topic. This is a guide search, not an automated vehicle diagnosis.